Vehicles
Sections
14 not categorized PORSCHE 997 TURBO FRONT ENDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1970-73 (includes uncategorized and accessory items) FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection KEV50303300
$1,549.90
Make a selection KEV50303400
$1,549.90
Make a selection FVD500911RSR Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) body kit that includes every detail for a perfect fit. This kit is not motorsports quality, it is OEM quality that sets it apart from the competition. Each part includes all the correct mounting cut outs, pre-drilled holes and fits like an OEM part for a perfect street car appearance. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight - made of high strength, grp (glass-reinforced plastic) kit contains: qty. 1 front bumper with spoiler, part # 10050305502 qty. 1 front bumper mounting kit, part # 10050305502mk qty. 1 rear bumper, part # 10050305503gf...(choose a part on the right to read more) General Fitment911 1970-73
From $9,222.99
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection 100505965 With front and rear steel fender flares including lights (front and rear head / tail and fog lights, blinkers), side skirts, installation hardware (all seals, gaskets, screws washers, nuts), cup mirrors and accessories. Without rear spoiler. General Fitment911 1970-73
$11,088.46
Make a selection FVD50599106MM The moshammer front bumper upper air vent is a combination of aggressive styling, aero-efficiency and increased cooling capacity. It is a motorsport finishing touch that complements the entire evo rs (991.2 turbo/s) / stormforce (991.1) / stormforce evo rs (991.2) or downforce rs (991.1 turbo/s) aero packages. FVD Brombacherhas a tradition of offering exclusive body styling that is functional, easily installed, wind tunnel tested, German made and TUV approved. Those high standards naturally led us to the moshammer brand. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment, superior durability and...(choose a part on the right to read more)
$371.80
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD50399701MM Louvers slats they are such a unique feature, so important. By opening the front fenders, and allowing the hot air from the brakes to get ventilated out of the wheel arch! To mount on top or bottom of the exist front fender. For all Porsche 997 Carrera | s | 4s | GTS | GT3 | targa | turbo s | GT2 | GT2 rs | sport classic
$640.20
Make a selection 90170110600 Finally a solution for the long missing factory id plate from your restored classic Porsche! from our friends in Germany who originally stamped them for the factory come the factory identical originally installed serial number plates for 911 and 912. These plates, identical in every way to the original were often lost when body men repaired these cars, cutting off and replacing the front panels. Over the years these aluminum plates take abuse from paint overspray and oxidation. Totally discontinued by the Porsche factory these are easily engraved with your vehicle identification number. A must for any restored Porsche. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 912 1965-69 911 1965-69
$37.85
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 1661900310 A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Please note: these are aftermarket calipers and do not come with the logo or brake pads. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98
$795.00
Make a selection 910165 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 930 1975-77 911 1970-73 911 1965-69 912 1965-69 914 1970-76
$458.05
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 99110613802 The radiator is a critical engine component that needs to be inspected and cleaned of debris to keep them functioning efficiently. If damage is noticed, replace it with this hello OEM high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the upper and lower rubber mounts, part # 99110653701 and 99110653802 sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. This part is the latest supersession and can also be used in place of part number 991 106 138 01.
From $1,042.80
Make a selection 90135196411 High-quality ate, OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $14.56
Make a selection 91135104120FSR Frozen slotted rotors are simply the best brake rotors money can buy. Serious drivers-those who tend to cross the finish line first--take their edge where they find it. And a growing number of them have embraced the edge that they’ve found in cryogenically treated brake rotors. Here’s why: they resist cracking, warping and fading; frozen rotors last 2-3 times longer than normal rotors; they stop consistently, lap after lap. Sold each. General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 930 1975-77 914 1970-76 924 1986-88 944 1982-85 944 1985-88 924 1980-85
$168.07
Make a selection 91135193500 A quality, cost effective "s caliper" reproduced by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Sold individually. 1 necessary per car. View/Change Diagram
From $306.08
Make a selection 91135193600 A quality, cost effective "s caliper" reproduced by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Sold individually. 1 necessary per car. View/Change Diagram
From $306.08
Make a selection 935FSUSP This light weight, bolt in kit replaces the factory front suspension arms, cross-member, and rubber bushings when converting to a coil over front suspension system. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$1,850.00
Make a selection EL2030900 Triangulation bests the single bar braces by increasing rigidity. traditional braces tie strut towers together force them to move in parallel, sharing the cornering force of the loaded tire over both towers to reduce flex. Triangulation locks the towers rigidly in place to maintain camber settings – even through high g corners. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$240.90
Make a selection P211L Front of rear fender, left. 1965-89. General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 912 1965-69
$105.00
Make a selection ER1T911SBF Quality and attention to detail make these sway bars the choice for serious performance. These elephant racing lightweight bars are hollow. They are half the weight of competing bars of equal stiffness. Bearing blocks, drop links, and sway bar arms are cnc machined from aircraft-quality 6061-t6 aluminum for its high strength/weight ratio. Fully adjustable front and rear drop links eliminate suspension preload. Oversized, precision teflon-lined rod-ends provide long life, smooth operation, and high-reliability. Adjustable drop-link arm connection design provides infinitely adjustable sway bar stiffness rate and makes it easy to fine-tune your car's handling for various track conditions and driving s...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76
$619.99
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection FVD503930001 Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) complete front fender set that includes headlight buckets and rear exit vents. Gas filler is not included with these fenders. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight left and right side. - made of high strength, grp (glass-reinforced plastic) sold as a set. 1 necessary per car. Please note: this only fits in conjunction with widebody / rsr rear bumper, part # 10050305503gfk and rear fenders, part # FVD503930003 . Please provide us with the year / model. These are high quality parts that take time to manufacture and cure properly. Lead tim...(choose a part on the right to read more) General Fitment911 1970-73
From $2,006.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |